UTMdev

Small Punch Test · EN 10371, clause 7 · Annexes C, D, F

Small Punch tensile and fracture test

The crosshead moves at a constant rate. A ball pushes through a small clamped disc until the disc fractures. The machine records the force against the deflection. Correlations give the proof strength, the tensile strength and an estimate of the fracture toughness.

  • 01Strength. 0.2 % proof strength Rp0.2 (Annex D) and tensile strength Rm (Annex C).
  • 02Energy. The small punch energy ESP, the base for the transition temperature.
  • 03Fracture toughness. Three estimates in Annex F.
0.2–2.0
mm/min crosshead rate (7.2.3)
0.5
mm/min rate of the EN 10371 steel correlations
≤ 10 %
of Fe: maximum preload (7.2.2)
3
recommended minimum number of tests (Annexes D, F)
Ask for a test Ask a technical question

EN 10371, 7.3

The force–deflection curve

The crosshead moves at a constant rate. The machine records the force F against the deflection u until the test piece fractures. The values for the correlations come from this curve.

Constant crosshead rate

Values from one curve

EN 10371 gets Fe from a bilinear fit (Figure 5), and Fi, Fm and um from the curve (Figure 7). The test ends when the force drops below 0.8 · Fm (7.2.5).

Small Punch Test force–deflection curve after EN 10371 Figures 5 and 7: elastic-plastic transition force F_e, force F_i, maximum force F_m at the deflection u_m and the small punch energy E_SP as the area below the curve
  • Fe — elastic-plastic transition force (7.3.1)Fe = fABilinear fit O–A–B when you record u, with uB = h0. Trilinear fit when you record v. Always report the method.
  • Fi — onset of plastic instability (7.3.3)Fi at uiFor the standard geometry and F(u), ui = 0.552 mm (Table C.1). Its position is almost independent of the tensile properties of the material.
  • Fm, um — maximum force and its deflection (7.3.4, 7.3.5)Fm, umThe maximum force of the test and its deflection.
  • ESP — small punch energy (7.3.6)ESP = ∫ F du, from 0 to umThe area below F(u) up to um.

If you record v in place of u, correct v for the compliance of the test rig (Annex A).

EN 10371, Annexes C, D, E, F

From the curve to material properties

The correlations of EN 10371 are empirical. They depend on the set-up geometry, and most of them come from steels. Use them with the standard geometry of Table 2.

Tensile strength Rm (Annex C)

Formula C.1: Rm = βRm · Fm / (h0 · um), with 0.19 ≤ βRm ≤ 0.32 for the standard geometry. Formula C.2: Rm = βRm · Fi / h0², with βRm = 0.192 for F(u) and 0.179 for F(v) (Table C.1). C.2 is verified on ferritic and martensitic steels only.

0.2 % proof strength Rp0.2 (Annex D)

Rp0.2 = βRp0.2 · Fe / h0². Table D.1: βRp0.2 = 0.510 for F(u) and 0.479 for F(v). The values are calibrated for steels with Rp0.2 of 200–1000 MPa. Do a minimum of three tests.

Fracture toughness (Annex F)

Annex F gives three estimates. The first is a correlation between TSP and KIc. The second is a correlation between the effective fracture strain and JIc. The third is δ on notched test pieces (notch radius 0.15 mm).

Effective fracture strain (Annex E, H)

εf = ln(h0 / hf), with hf the thickness at fracture. Measure hf on a section, with 3D optical microscopy or with X-ray CT.

Component in service?

Sampling and tests as a service

Sampling: we take a scoop sample on site from a cold component. Tests: send us your material. We do the Small Punch tests and send you a test report to EN 10371.

Ask for a test How we take the sample

Method pages

Other parts of the method

OverviewThe Small Punch TestPrinciple, the tests, comparison with conventional tests, history and FAQ.to the overview →Small Punch | CreepSmall Punch Creep TestEN 10371, clause 8 · Annex GConstant force at high temperature: creep curve, minimum deflection rate, time to rupture, equivalent stress.to the creep test →Small Punch | Transition temperatureSmall punch transition temperatureEN 10371, Annex ETests at different temperatures: normalised energy, tanh fit, TSP and the link to Charpy.to the transition temperature →Small Punch | Test piecesFrom the component to the test pieceEN 10371, clause 5Scoop sample, discs Ø8 × 0.5 mm or Ø3 × 0.25 mm, grinding and the tolerances of Table 1.to sampling and test pieces →

The next step

The machines for this test

SPC 1200 Small Punch Test machine

SPC line

Four machines for creep tests and for tensile and fracture tests, from room temperature to 650, 800, 1000 or 1200 °C.

650–1200 °C
four temperature classes
to 5000 N
constant force
Ø8 · Ø3 mm
test pieces
To the SPC line →
TTS 190 Small Punch Test system with cryogenic chamber

TTS 190

Tensile and fracture tests from +23 °C to −193 °C, with automatic cooling and evaluation.

−193 °C
lowest test temperature
±1 °C
on the test piece
10 kN
force capacity
To the TTS 190 →

No machine yet? We do the tests for you.

Request more information

Tell us what you need to test

Tell us the material, the temperature and the property that you need. We propose test conditions or a machine configuration.

  • We reply in 5 working days
  • We send leaflets by email
  • For service-exposed components we add a sampling proposal

UTMdev s. r. o., Ostrava, Czech Republic
info@utmdev.eu · +420 608 615 303

Request more information

Data protection notice

Information on data processing can be found in our privacy statement.

Mandatory